超高强7055铝合金铸锭均匀化工艺优化

采用光学显微镜、扫描电镜、差热分析及透射电镜等手段,对一种航空用超高强7055铝合金大尺寸铸锭的均匀化工艺进行分析与优化。提出分级提高均匀化温度的方法,在确保不发生过烧的情况下,最大限度改善铸锭质量。结果显示:低温预均匀化时,铸锭中析出大量的Al₃Zr相,能够大幅度降低对后续挤压变形的再结晶比例;对铸锭采用400 ℃×4 h+465 ℃×16 h+474 ℃×8 h的分级均匀化处理工艺,能够显著消除铸锭中低熔点相的含量,提高铸锭质量,同时相比于原工艺节省约13 h。新的均匀化处理工艺,不仅提高了生产效率,还能够为后续工艺提供良好的铸锭。     

Theoretical and Experimental Studies for the Transient Response of Cavity

During the transient state of aero-engine,cavity has evidently transient characteristics in the secondary air system.To investigate transient characteristics,theoretical and experimental studies were implemented for both static and rotating cavities.First of all,the typical transient response phenomena in secondary air system were investigated based on the basic concepts of the dynamic process.According to the basic theory of gas dynamics,the causes of transient phenomena were analyzed in two aspects,external disturbance,and system physical properties.Several dimensionless parameters were introduced to analyze the transient response characteristics of air system.Second,the experimental results of the static cavity indicated that the actual response time increased with the increase of the inlet pressure.The experimental results of the rotor-stator cavity showed that the low rotational speed on the response process had little effect,and the response time gradually increased when the speed continued to increase.Third,the test results of multiple components suggested that when the valve was opening the inlet pressure of the static cavity increased quickly and then reached a stable value,but the pressure of the static cavity,stable pressure cavity and rotor-stator chamber rose gradually.It was also obtained the actual response time of them was increased.The closer the measuring points were to the disturbance source,the shorter the delay time was.     

两种不同培养工艺制备森林脑炎灭活疫苗的免疫原性及安全性评价

目的评价细胞工厂工艺制备森林脑炎灭活疫苗的免疫原性及安全性。方法利用10 L转瓶和细胞工厂两种工艺在地鼠肾细胞上培养森林脑炎病毒(tick-borne encephalitis virus,TBEV),收获病毒液,经病毒灭活、超滤浓缩、柱层析纯化、除菌过滤后,制备森林脑炎灭活疫苗。采用透射电子显微镜及SDS-PAGE对病毒进行形态观察及鉴定。将两种工艺共制备的6批疫苗免疫小白鼠,评价疫苗的免疫原性;通过家兔刺激试验及豚鼠主动过敏性试验评价疫苗的安全性。结果两种工艺共制备的6批疫苗原液,透射电镜下观察均可见约为50 nm的圆形病毒颗粒,SDS-PAGE分析均可见相对分子质量分别为50 000和40 000~45 000的蛋白条带,病毒形态及蛋白条带大小均与TBEV相符;免疫保护指数均大于1. 0×10~5,符合《中国药典》三部(2015版)标准;家兔刺激试验对注射部位无刺激性,豚鼠主动过敏试验无小鼠出现过敏性反应。结论细胞工厂工艺和10 L转瓶工艺制备的森林脑炎灭活疫苗均具有良好的免疫原性及安全性。     

湿法氧化锌种类和用量对天然橡胶性能的影响

研究湿法氧化锌种类和用量对天然橡胶(NR)性能的影响。结果表明:与添加普通氧化锌的胶料相比,对于未填充炭黑NR体系,减半用量的湿法氧化锌混炼胶的焦烧时间和t90较短,Fmax较大;硫化胶的定伸应力、拉伸强度和剪切模量(G′)较大,拉断伸长率、损耗模量(G″)和损耗因子(tanδ)较小。对于填充炭黑NR体系,减半用量的湿法氧化锌混炼胶的门尼粘度、G′和G″较大,tanδ较小,焦烧时间和t90较短,Fmax较大;硫化胶的密度稍低,硬度和定伸应力较大,耐老化性能较好,玻璃化温度较低,tanδ较小,其他物理性能变化不大。湿法氧化锌FF的性能优于湿法氧化锌HR。     

FDM 3D打印工艺参数对PLA制件力学性能的影响

采用五因素四水平正交试验设计,对16组不同工艺参数(打印层厚、填充密度、打印温度、填充速度、外壳厚度)的FDM 3D打印聚乳酸(PLA)制件力学性能进行了测试和结果分析,确定了影响PLA制件力学性能的主要因素,其中,外壳厚度对制件力学性能影响最为明显,打印温度影响最小,同时分析得到了在打印层厚0.15 mm,填充密度40%,打印温度210℃,填充速度60 mm/s,外壳厚度1.6 mm条件下可获得力学性能最佳的制件。最后对试验数据进行回归分析,拟合得到了FDM打印工艺参数与PLA制件力学性能指标的数学模型;通过对不同打印工艺参数的试样进行试验验证,表明该模型拟合误差小(5%以内),可靠性高,可用来对FDM 3D打印制件的加工提供参考。     

短程反硝化耦合厌氧氨氧化工艺及其应用前景研究进展

短程反硝化以其碳源消耗量、废污泥产量、温室气体排量极低及无需曝气等优势，被认为是最具研究潜势的厌氧氨氧化底物供给技术，成为近年来研究热点。本文首先介绍了短程反硝化工艺原理；其次从污泥源、反应时间、碳源类型、碳源量及pH等5个方面总结了影响短程反硝化工艺启动因素；随后综述了短程反硝化耦合厌氧氨氧化工艺的重要研究进展，同时指出了耦合工艺实验研究与工程应用的不足，并提出了解决实验与工程应用缺陷的方案；最后展望了耦合工艺处理城市污水和工业硝酸盐废水的可行性及应用前景，认为全面分析工业硝酸盐废水化学组分与基于分子生物学水平的宏基因组学测序、元转录组学技术是未来耦合工艺同步处理城市污水和工业硝酸盐废水的研究重点。     

某高硫铜硫矿工艺矿物学研究

研究了某高硫铜硫矿的工艺矿物学。结果表明,原矿中铜品位为2.85%,硫品位为24.32%,金含量为0.48g/t,铜、硫、金是主要回收的元素。原矿中的金属矿物有黄铜矿、黄铁矿、蓝辉铜矿。目的矿物黄铜矿和黄铁矿的嵌布粒度差异较大,且铜矿单体解离度相对较差。在选择工艺流程时应该注重氧化铜矿物的回收,同时要选择合适的磨矿细度,保证目的矿物单体解离。     

Solution processed,vertically aligned,AZO nanocolumn array for chemiresistive sensor application with UV-enhanced sensitivity

In this work, a wide and highly sensitive chemiresistive sensor has been developed based on the AZO nanocolumn array film. This is meant for the room detection of H₂O₂ under UV illumination. A cost-effective one step multi-layers growth process was adopted for the synthesis of the AZO nanocolumn array. The experimental studies were done by scanning electron microscopy (SEM), transmission and electron microscopy (TEM).Then X-ray diffraction confirmed that the AZO column array was closely packed, connected, vertically aligned, and polycrystalline, with a high surface area. This structure ensures better electrical conduction over random and separated nanostructures. The hall-effect measurement indicates that the AZO film was n-type, with high conductivity (3.60 × 10³ Ωcm), high carrier density (11.3 × 10²⁰cm⁻³) and with acceptable mobility (0.95 cm²/Vs). The x-ray photoemission spectroscopy suggests that the AZO film consists of a large amount of adsorbed oxygen-related species at the sheath layer of the thin-film, which is vital for sensors. By the UV light activation, sensors based on the AZO nanocolumn array exhibited enhanced H₂O₂ detection properties at room temperature. At a concentration from 15 μM to 30 mM, H₂O₂ sensitivity evaluated by relative response was remarkably increased from 15% to 36%. The operation under ambient conditions and wide range sensing shows that this chemiresistive AZO sensor is adequate for biomedical and environmental applications.     

Effects of risks on the performance of business process outsourcing projects: The moderating roles of knowledge management capabilities

Although business process outsourcing (BPO) can reduce cost and enhance the competitiveness of firms, the implementation of BPO projects is unsatisfactory. By integrating knowledge management capability theory and risk-based view, we develop a model of how different types of BPO risks affect project satisfaction and how knowledge management capability changes the influences of BPO risks. A survey of 121 BPO projects was conducted among BPO client department manager and project manager through a pairwise design. Empirical evidence reveals that social system, technical system, and project management risks negatively affect BPO project satisfaction. However, cultural, technological, and structural levels of knowledge management capabilities weaken the negative risk effects of social system, technical system, and project management, respectively. Different types of risks and knowledge management capabilities should be matched to achieve effective risk management.